Common Problems on Matrix Pumps and the Fastest Ways to Fix them

Genuine distributor T&C Industrial Distribution (T-CID)

Multi-stage centrifugal pump series Ebara MatrixRenowned for its durability and high performance in industrial applications. However, no matter how high-end the equipment is, after a long period of operation in harsh environments, the pump can still encounter unexpected technical problems. As an in-depth technical support and distribution unit, T&C Industrial Distribution (T-Cid)has compiled the 4 most common problems on Matrix pumps along with a quick handling process to help the factory operations team optimize downtime.

1. The pump does not pump water or the flow is weak

  • This is a common phenomenon, often stemming from hydraulic or piping problems.
  • Cause:

    • The pump has air leakage in the suction pipe (air leakage).

    • The one-way valve or valve is stuck/broken, causing loss of primer water.

    • Garbage blockage in the suction filter (strainer).

  • The pump has air leakage in the suction pipe (air leakage).

  • The one-way valve or valve is stuck/broken, causing loss of primer water.

  • Garbage blockage in the suction filter (strainer).

  • How to handle:

    1. Check the suction pipe joints, tighten them or replace the gaskets if there are signs of air leakage.

    2. Check and clean the Y-strainer to see if it is clogged.

    3. Reprime the pump and ensure the one-way valve operates smoothly.

  • Check the suction pipe joints, tighten them or replace the gaskets if there are signs of air leakage.

  • Check and clean the Y-strainer to see if it is clogged.

  • Reprime the pump and ensure the one-way valve operates smoothly.

2. The pump makes strange noises and vibrates strongly

  • Excessive vibration is the “enemy” of bearings and mechanical seals and should be dealt with immediately.
  • Cause:

    • The pump becomes misaligned with the motor after a period of operation.

    • Bearings are damaged or lacking lubricant.

    • Cavitation occurs due to too low input pressure.

  • The pump becomes misaligned with the motor after a period of operation.

  • Bearings are damaged or lacking lubricant.

  • Cavitation occurs due to too low input pressure.

  • How to handle:

    1. Check the concentricity of the pump shaft and motor shaft with a specialized laser measuring device.

    2. Check to see if the bearings are unusually hot or making screeching noises; If so, genuine bearings need to be replaced.

    3. Check suction head pressure; If the pump is “dry suction”, increase the pressure or recheck the inlet piping.

  • Check the concentricity of the pump shaft and motor shaft with a specialized laser measuring device.

  • Check to see if the bearings are unusually hot or making screeching noises; If so, genuine bearings need to be replaced.

  • Check suction head pressure; If the pump is “dry suction”, increase the pressure or recheck the inlet piping.

3. Water leak at the mechanical seal part (Mechanical Seal)

  • The mechanical seal is the most “sensitive” part on the Matrix pump. When the seal is broken, water will leak out through the pump shaft.
  • Cause:

    • Running the pump without water for a long time (causing burned seals).

    • The transport fluid contains too much dirt/corrosive chemicals that scratch the seal surface.

  • Running the pump without water for a long time (causing burned seals).

  • The transport fluid contains too much dirt/corrosive chemicals that scratch the seal surface.

  • How to handle:

    1. Turn off the machine immediately to avoid damaging the pump shaft.

    2. Remove the seal assembly for inspection. If the felt mirror surface is scratched or chipped, it is mandatory Replace new seal.

    3. Make sure the input water source is clean and always maintain priming water before starting the machine.

  • Turn off the machine immediately to avoid damaging the pump shaft.

  • Remove the seal assembly for inspection. If the felt mirror surface is scratched or chipped, it is mandatory Replace new seal.

  • Make sure the input water source is clean and always maintain priming water before starting the machine.

4. The motor is overloaded and the CB jumps

  • When the motor operates beyond its designed capacity, the protection system will automatically turn off the power.
  • Cause:

    • The output water flow is too large (the pump is working beyond its efficiency point – BEP).

    • The supply voltage is unstable (voltage drop or phase loss).

    • The motor is stuck due to a locked bearing or shaft.

  • The output water flow is too large (the pump is working beyond its efficiency point – BEP).

  • The supply voltage is unstable (voltage drop or phase loss).

  • The motor is stuck due to a locked bearing or shaft.

  • How to handle:

    1. Use a clamp meter to measure the actual current of the motor and compare it with the parameters on the machine label.

    2. If the flow is higher than rated, use a gate valve at the discharge end to do so reduce trafficuntil the current returns to a stable level.

    3. Check the power supply and the smoothness of the pump shaft when turning by hand (when the machine is disconnected).

  • Use a clamp meter to measure the actual current of the motor and compare it with the parameters on the machine label.

  • If the flow is higher than rated, use a gate valve at the discharge end to do so reduce trafficuntil the current returns to a stable level.

  • Check the power supply and the smoothness of the pump shaft when turning by hand (when the machine is disconnected).

Advice from experts at T&C Industrial Distribution (T-Cid)

  • Quick troubleshooting is only “the tip”. For the system to operate reliably for over 10 years, we recommend that you:
  • Perform routine maintenance:Check vibration, bearing temperature and seal tightness every 3-6 months.

  • Always use genuine spare parts:Especially bearings and seals. Using floating cargo not only reduces pump life but also causes chain damage.

  • Connect with the support team:Technical team of T&C Industrial Distribution (T-Cid)Always ready to support inspection and troubleshooting at the scene.

  • Is your system having problems?Don’t hesitate to contact immediately T-Cid. We not only provide quick solutions but also advise on problem prevention options to help your system always operate smoothly.

CONTACT YOUR TECHNICAL SUPPORT REPRESENTATIVE AND QUOTE

General Distributor T&C Industrial Distribution (T-CID)
📞 Technical contact hotline: 0903 071 804
📍 Warehouse general agent address:384/42 Nam Ky Khoi Nghia, Hoa Xuan Ward, City. HCM
🌐 Look up online catalogs: Ebaravietnam.vn